This great article listed below pertaining to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is indeed interesting. Give it a go and make your own assumptions.
Setting up a tub isn't exactly rocket science, however it does call for solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old bathtub with a new one is also a moderately difficult task. If the old bathtub is easily accessible, the task can relocate immediately; if you have to open a wall surface to eliminate the old tub as well as position the brand-new tub, the task is much harder. In either situation, the project is within a home handyman's abilities, although you will require a helper to move out the old tub and set in the new one. Make certain you have actually certified on your own for the task and also are comfortable trying it. Instead of hiring a contractor to take control of a halfway-completed project, it is far better to think about employing one before you start. Opportunities are you may need an expert plumber to make tube links.
This write-up will certainly aid you mount a brand-new bathtub in your bathroom if you have actually currently acquired a new bathtub as well as don't require to alter the plan of your previous water supply pipelines.
Your tools as well as product list ought to comprise the following:
Removing Old Touches
If you require to change old taps with new ones as a part of your installment, after that the first thing you should do is disconnect the water. After doing so, switch on the faucets to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be fairly problematic due to the restricted access that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the taps. Have a towel ready for the staying water that will certainly come from the pipelines. Once the supply pipelines have actually been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning throughout this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any old sealing compound.
Prior to moving on to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic adapter to stop damage to the string. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will call for minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washers are in place in between the faucet and the sink. Secure the tap in place with the producer supplied backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be connected by using corrugated copper piping or with normal tap connectors. The former kind ought to be connected to the faucet ends first, tightening up just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Mounting the Bath tub
Utilizing both wooden boards under its feet, place the bathtub in the needed position. The wooden boards are handy in evenly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto 4 little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by examining the level as well as adjusting the feet on the tub till the level checks out degree.
To mount taps, fit the bottom of the furthest versatile tap adapter to the appropriate supply pipeline by making a compression join; then do the very same for the various other faucet.
Switch on the supply of water and examine all joints and also new pipework for leaks as well as tighten them if required. Fill the bathtub and additionally examine the overflow electrical outlet and the normal electrical outlet for leaks.
Lastly, repair the bath paneling as explained in the supplier's user's manual. Tiling as well as securing around the bathtub needs to wait until the bathtub has been made use of at the very least when as this will resolve it right into its final placement.
Planning for the Installation
To start with, the supporting framework supplied with the bath should be fitted (if called for) according to the manufacturer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to see to it that if the tap includes a plastic washer, it is fitted between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now prepare to be fitted in its last placement.
Tiling Around the Tub
In the location where the bath fulfills the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a rigid seal, creating the water to pass through the wall surface in between the bathroom as well as the tiling, bring about issues with wetness and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to assimilate your fixtures and also installations. They are marketed in tubes and also cartridges, and also are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of soaked newspaper or soft rope. Remember to always fill up the bath tub with water before sealing, to permit the movement experienced when the tub is in use. The sealant can crack rather very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise conveniently offered on the marketplace. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been guided to that article about Installing A Bathtub from someone on another web blog. Sharing is good. Helping others is fun. We treasure reading our article about How to Install a Bathtub.
Request plumbing analysis.